Getting Started
Using a CRA-2 with your ELMO Camera
There are a couple of ways to use your CRA-2 with your ELMO Camera. Below are example setups you can use to pair your devices together. For a more complete overview of the CRA-2, please see our CRA-2 Overview page. With a computer and ELMO Software ...
How to factory reset a STEM camera (TT-12W, MA-1, MO-2)
If your camera is crashing, freezing, or having other issues, a factory reset is recommended. TT-12W and MO-2 models must be connected to a external display (TV, Monitor, Projector ; not a Computer) to enter the settings menus. Instructions can be ...
Example setups for using your Document Camera
There are a number of ways you can use your camera. Below are just a few common setups you can use with your devices. Not all setups can be used with all ELMO devices. Please refer to the device specifications for detailed port availability on your ...
Connecting your TT-12G Camera to an ELMO Cast
1. Identify the HDMI input ports available on your display. Connect the ELMO Cast to the HDMI input, and then connect the ELMO Cast to power over USB. 2. Switch the display input to the ELMO Cast. Take note of the device name. More info about the ...
SD Card identification guide
Cable Identification Guide
Connecting your Wireless STEM Camera (MA-1, MO-2, and TT-12W) to an ELMO Cast
1. Identify the HDMI input ports available on your display. Connect the ELMO Cast to the HDMI input, and then connect the ELMO Cast to power over USB. 2. Switch the display input to the ELMO Cast. Take note of the device name. More info about the ...
Using an ELMO Document Camera with a Third-Party Interactive Display
Connecting via USB - Direct Connect your document camera to your display using the proper USB cable. If your interactive display has a preinstalled camera application, you may be able to use this application to view your document camera. With a ...
Connecting your Camera to a TV or Monitor
1. Identify the video input ports available on your display and compare them to the video out ports on your ELMO camera. The ports will be labeled as 'OUT' on your camera. Please note that the ports available will vary depending on the model of your ...
Connecting your Camera to a Computer
1. Identify the USB Ports on your computer and ELMO. [EXAMPLE ELMO PRODUCTS; PORTS MAY VARY] [Computers] 2. Find the right software for your camera and computer combination on our website and install it. You can also check the user manual packaged ...
Setting up a Hybrid viewing experience (simultaneous in person and virtual audiences)
1. Identify the video input ports available on your display device (Projector, Monitor, IFP) and compare them to the video out ports on your computer. [Projector] [Display] [Computers] 2. Connect your computer to the display. Then, connect your ELMO ...
Setting up HDMI or VGA Passthrough
1. Identify the video input ports available on your display device (Projector, Monitor, IFP) and compare them to the video out ports on your ELMO camera. The ports will be labeled as 'OUT' on your camera. Please note that the ports available will ...
Connecting your Camera to a Projector
1. Identify the video input ports available on your projector and compare them to the video out ports on your ELMO camera. The ports will be labeled as 'OUT' on your camera. Please note that the ports available will vary depending on the model of ...
Software and Drivers Downloads
Looking for software or drivers? Please visit our software page. All software requires a USB connection from your ELMO to your computer. If you're having trouble picking out the right software for your setup, please contact our support team.
Setting up your ELMO STEM Cam (TT-12W, MA-1, MO-2) for USB Connection
This article will explain how to setup your new ELMO STEM Cam for USB connection. Most TT-12W, MA-1, and MO-2 cameras will require this guide, but not all steps may be necessary. After following this guide, please see our guide for Connecting your ...